Right axle height sensor is faulty.

The angle sensor that measures the spring deflection for the right wheel is defective.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

Drawbar height sensor is faulty.

The angle sensor that measures the spring deflection for the drawbar is defective.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

Target height of the axle cannot be maintained.

The planned height of the axle or drawbar cannot be reached within the defined time.

Mechanical, hydraulic or electrical malfunction.

Contact Customer Service.

Target height of the drawbar cannot be maintained.

Calibration of the suspension is required.

Calibrate the suspension.

Suspension: Check parameters.

Values in the configuration outside of the valid range.

Pressure out of reach.

The regulation cannot reach the desired pressure.

Check the air supply to the nozzles and the pressure sensor.

The speed is too high.

The desired pressure at the nozzle cannot be reached.

The speed is too low.

The desired pressure at the nozzle cannot be reached.

Defective angle sensor.

Angle sensor that determines the boom slope is defective.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

SPRAYER

Defective slope sensor.

The slope sensor installed on the frame of the field sprayer is defective or was not configured.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

The sensor is used both for DISTANCE-Control and for TRAIL-Control, and is therefore calibrated with each of these systems.

BOOM

Defective slope sensor.

The slope sensor installed on the boom of the field sprayer is defective or was not configured.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

Defective right US-sensor.

The first echo of the ultrasonic sensor is not coming back. Sensor or cable is defective.

Defective left US sensor.

The first echo of the ultrasonic sensor is not coming back. Sensor or cable is defective.

Sensors are disturbed.

Short signal interruption with all sensors.

An actuator might be connected to the sensor ground (GNDE) in the junction box.

Defective height angle sensor.

Angle sensor that measures the height of the lift pole is defective.

This error message only appears on a few field sprayers that have manufacturer-specific configuration.

No right ultrasonic signal.

There is no echo coming back for more than 50% of the trigger impulses.

No left ultrasonic signal.

There is no echo coming back for more than 50% of the trigger impulses.

The slope sensor is not correctly installed.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

The slope angle sensor is not correctly installed.

The signal voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

The ultrasonic sensors are not correctly installed.

The sensors are connected inversely. (Left and right were inverted in the junction box)

No slope sensor signal.

In the second calibration step, the slope sensor did not detect a change in the signal.

No angle sensor signal.

In the third calibration step, the angle sensor did not detect a change in the signal.

Outlets are swapped.

The hydraulic valves were connected wrong.

Sensors are disturbed.

Short signal interruption with all sensors

BOOM

Out of transport position.

The alarm is coupled to the Id37 input function. Display via graphic in the boom and alarm message.

BOOM

No locking.

Alarm appears when no signal is received from the boom locking sensor.

Defective angle sensor.

Alarm when boom height control system is configured but the boom potentiometer is recognized as defective.

Low tank content.

The volume of spray liquid in the tank has fallen below the "Tank level alarm".

SPRAYER

Pump speed is too low.

Check the pump speed.

Switch on the pump.

Increase the pump speed.

SPRAYER

Pump speed is too fast.

Check the pump speed.

Decrease the pump speed.

Boom folding forbidden: The speed is too high.

The boom may only be folded and unfolded when the sprayer is at a standstill.

SPRAYER

Pump oil level.

Alarm appears when a sensor detects a certain oil level. The oil level depends on the implement manufacturer and the installation of the sensor.

The compressor is too slow.

The compressor is slower than the defined value.

The compressor is too fast.

The compressor is too fast.

Filter pressure too high.

The pressure switch on the filter is sending an error message.

The left ladder is not in transport position.

Static signal from a sensor that checks the position of the ladder.

The right ladder is not in transport position.

Field mode is activated.

Alarm appears when the "Tractor-ECU" job computer sends a signal that the mode was switched from driving on the road to driving on the field.

When driving on the road, the joystick buttons will be ignored.

Axle not locked.

Appears when a maximum speed that was defined for unlocked axles has been exceeded. The speed is defined by the implement manufacturer.

Lock the axle.

The implement is being operated using an external device! To cancel, acknowledge this alarm.

The field sprayer is currently not being operated using the terminal, rather via an external input device. To terminate the external operation, acknowledge the alarm. You will then be able to operate the controls again.

SPRAY REGULATION

Set rate out of reach.

The system cannot adjust the application rate to the rate.

SPRAY REGULATION

The pressure is too low

The minimum spray pressure could not be reached. Parameter: Min. pressure

SPRAY REGULATION

The pressure is too high

Pressure is higher than defined in the parameter. Parameter: Max. pressure

L/min too high, above flow meter specifications.

Flow is too high. The flow meter is not capable of measuring reliably.

L/min too low, below flow meter specifications.

Flow is too low. The flow meter is not capable of measuring reliably.

To change the parameter, the password must first be entered.

The function that you want to perform is only available after entering the password.

Defective drawbar angle sensor.

The analog input voltage is outside of the valid range.

Valid range: 0.5 V to 4.5 V

Defective slope sensor.

The analog input voltage is outside of the valid range. Valid range: 0.5 V to 4.5 V

Defective gyroscope.

The analog input voltage is outside of the valid range. Valid range: 0.5 V to 4.5 V

Calibration must be performed

No valid value for the drawbar middle position.

Check parameters

Values in the configuration outside of the valid range:

With drawbar steering:

Drawbar length: 80cm - 300cm

Frame length: 100cm - 500cm

With stub axle steering:

Drawbar length: 200cm - 800cm

The slope sensor is not correctly mounted

Valid voltage range during calibration: 1.5V to 3.5V

The drawbar angle sensor is not correctly installed.

Valid voltage range during calibration: 1.5V to 3.5V

The gyroscope is not correctly installed.

Valid voltage range during calibration: 1.5V to 3.5V

The drawbar angle sensor is reversed.

The wrong direction of rotation was detected during calibration of the limit stops.

Sensors are disturbed

Short signal interruptions with all sensors

No overlap in Vario mode: Change nozzles or set a wider pressure range.

The installed nozzles are not capable of reaching all of the target rates in the selected range. You may require different nozzles.

See: Before you buy nozzles - check the possible application rates

Check also if the installed nozzles were properly selected:

Configuring the nozzles on the multiple nozzle holder

Vario mode requires at least 2 nozzles.

Ensure that at least two nozzles are installed on each nozzle holder and that these nozzles are also set in the software. See: Configuring the nozzles on the multiple nozzle holder

Enter the user password to continue.

The setting is password-protected.

Enter the service password to continue.

The setting is password-protected.